Cat 907 Compact Wheel Loader

Maximum Gross Power

74.7hp

Engine Model

Cat C2.8*

Maximum Engine Speed

2550 rpm

Maximum Gross Power – Rated Engine Speed

2400r/min

Maximum Gross Power – SAE J1995

74.7hp

Maximum Gross Power – ISO 14396

74.3hp

Maximum Gross Power – ISO 14396 (metric)

75.3mhp

Rated Net Power – Rated Engine Speed

2400r/min

Rated Net Power – SAE J1349

72.7hp

Rated Net Power – ISO 9249

72.1hp

Rated Net Power – 2,400 rpm – ISO 9249 (metric)

73.1mhp

Maximum Gross Torque – SAE J1995

222lb/ft

Maximum Gross Torque – ISO 14396

221lb/ft

Maximum Net Torque – SAE J1349

218lb/ft

Maximum Net Torque – ISO 9249

217lb/ft

Displacement

171in³

Bore

3.54in

Stroke

4.33in

Note

*Meets U.S. EPA Tier 4 Final and EU Stage V emission standards.

Note (1)

Advertised power is tested per the specified standard in effect at the time of manufacture.

Note (2)

Net power advertised is the power available at the flywheel.

Note (3)

#Maximum gross and net torque measured at 1,600 rpm.

Operating Weight

12765lb

Bucket Capacities

0.75-1.55 m³ (1.0-2.0 yd³)

Bucket Capacities – General Purpose

0.80-1.35 m³ (1.0-1.7 yd³)

Bucket Capacities – Light Material

1.25-1.55 m³ (1.6-2.0 yd³)

Multi-Purpose

0.75-1.1 m³ (1.0-1.4 yd³)

Note

Bucket selection must be made with an understanding of the material density and application to ensure machine stability is maintained within the tipping loads stated per model and configuration.

Note (1)

Bucket capacities stated include BOCE, in line with ISO 7546.

Recyclability

93%

Fuel Tank

24Gal

Cooling System

3.2Gal

Engine Crankcase

2.3Gal

Axles – Front Center Differential

2.3Gal

Axles – Rear Center Differential

2.3Gal

Hydraulic System – Including Tank

17.8Gal

Hydraulic Tank

11.8Gal

Transmission

0.6Gal

Note

No Diesel Exhaust Fluid (DEF) fluid needed on this size engine.

Front

Fixed (standard), Locking Differential (optional)

Rear

Fixed (standard), Locking Differential (optional)

Note

Oscillation of ±11 degrees via hitch between front and rear frames.

Steering Articulation Angle – Each Direction

39°

Maximum Flow – Steering Pump

12.3gal/min

Maximum Working Pressure – Steering Pump

3336psi

Steering Cycle Times – (full left to full right) – at High Idle

2.8s

Number of Steering Wheel Turns – Full Left to Full Right or Full Right to Full Left

3.25 turns or 4.00 turns

Forward and Reverse – Speed Range Creep#

6mile/h

Forward and Reverse – Speed Range 1*

6mile/h

Forward and Reverse – Speed Range 2** – High Speed

10.5mile/h

Forward and Reverse – Speed Range 2** – Standard

12mile/h

Forward and Reverse – Speed Range 3***

25mile/h

Note

#Factory default shown, can be adjusted to any speed up to 19 km/h (12 mph).

Note (1)

*Creep function not available in this gear or above.

Note (2)

**Max speed dependent on model and configuration (standard vs. high speed transmission).

Note (3)

***Reverse is 30 km/h (19 mph).

Tire Size – Standard

*405/70 R18 SPT9

Tire Size – Optional

405/70 R18 Powerloads

Tire Size – Optional (1)

340/80 R18 XMCL/Bibload

Tire Size – Optional (2)

340/80 R18 TRI 2

Tire Size – Optional (3)

40X14-20 TL, SM/TR

Tire Size – Optional 4

340/80 R18 Duraforce

Note

*This tire has been used for all dimension, stability and performance data.

Note (1)

Other tire choices are available. Contact your Cat dealer for details.

Note (2)

Caterpillar recommends that you consult a tire supplier to evaluate all conditions before selecting a tire model.

ROPS

ISO 3471:2008

FOPS

ISO 3449:2005 Level II

Note (1)

Canopy and cab, Rollover Protective Structures (ROPS) are available worldwide. Canopy not available in EU.

Note (2)

The declared dynamic operator sound pressure levels per ISO 6396:2008*, when properly installed and maintained, is 71 dB(A).

Note (3)

*Measurements were conducted with the cab doors and windows closed.

Note (4)

The labelled sound power level for the CE marked configurations when measured according to the test procedure and conditions specified in 2000/14/EC is 101 dB(A). 99 dB(A) Low Sound – Option available.

Main Relief – 1st Auxiliary (3rd slice)

3408psi

Main Relief – 1st Auxiliary (3rd slice) – Standard Flow*

21gal/min

Main Relief – 1st Auxiliary (3rd slice) – High Flow*

32gal/min

Main Relief – 2nd Auxiliary (4th slice)

3408psi

Main Relief – 2nd Auxiliary (4th slice) – Flow

12gal/min

Hydraulic Cycle Time – Rackback

2.2s

Hydraulic Cycle Time – Lift

Hydraulic Cycle Time – Dump

1.6s

Hydraulic Cycle Time – Float Down

2.8s

Note

* Maximum flow stated, actual flow delta could be 6% from data shown. Also adjustable from 20% to 100% of maximum flow through display.

Height: Ground to Cab**

8.5ft

Height: Ground to Beacon**

9.08ft

Height: Ground Axle Center**

1.58ft

Height: Ground Clearance**

1ft

Length: Overall*

17.58ft

Length: Rear Axle to Bumper

4.58ft

Length: Hitch to Front Axle

3.58ft

Length: Wheel Base

7.08ft

Length: Front Axle to Front of Coupler

3.5ft

Clearance: Bucket at 45° *

8.25ft

Clearance: Load over Height**

9.5ft

Clearance: Level Bucket**

9.92ft

Height: Bucket Pin**

10.67ft

Height: Overall**

13.5ft

Reach: Bucket at 45° *

2.33ft

Carry Height: Bucket Pin

1.08ft

Dig Depth**

0.33in

Width: Bucket

6.75ft

Width: Tread Center

4.67ft

Turning Radius: Over Bucket

14.75ft

Width: Over Tires

6.07ft

Turning Radius: Outside of Tires

12.92ft

Turning Radius: Inside of Tires

6.75ft

Rack Angle at Full Lift

56°

Dump Angle at Full Lift

45°

Rack Angle at Carry

51°

Departure Angle – Degrees

30°

Articulation Angle – Degrees

39°

Operating Weight: Bucket ^

12689lb

Tipping Load – Straight – ISO 14397-1 †

9773lb

Tipping Load – Full Turn – ISO 14397-1 †

8235lb

Operating Weight: Carriage and Tines ^^

12220lb

Tipping Load – Straight †

7807lb

Tipping Load – Full Turn †

6569lb

80% of Tip: Firm and Level EN474-3 ††

5255lb

Note (1)

*Vary with bucket

Note (2)

**Vary with tire

Note (3)

^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL),1.05 m3 (1.4 yd3) general purpose bucket.

Note (4)

^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class II carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center).

Note (5)

†Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing.

Note (6)

††Full compliance to EN474-3 and SAE J1197.

Note (7)

#HPL-A weight, tipping and rated loads are within 1% of the HPL-V.

Note (8)

Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9 405/70 R18 tires and 1.05 m3 (1.4 yd3) general purpose bucket with bolt-on cutting edge or a class II

Note (9)

Note: Goodyear POWERLOAD® tires can add up to approximately 140 kg (305 lb) to the full turn tip load and reduce vertical height by approximately 25 mm (1 in) compared to SPT9.

Height – Ground to Cab

8.5ft

Height: Ground to Beacon**

9.08ft

Height: Ground Axle Center**

1.58ft

Height – Ground Clearance

1ft

Length – Overall with Bucket

18.17ft

Length: Rear Axle to Bumper

4.58ft

Length: Hitch to Front Axle

3.58ft

Length – Wheel Base

7.08ft

Length: Front Axle to Front of Coupler

4.33ft

Clearance – Bucket at 45°

7.83ft

Clearance: Load over Height**

9.5ft

Clearance – Level Bucket

9.92ft

Height – Bucket Pin

10.67ft

Height: Overall**

13.83ft

Reach – Bucket at 45°

2.67ft

Carry Height: Bucket Pin

1.17ft

Dig Depth

3in

Width – Bucket

6.75ft

Width – Tread Center

4.67ft

Turning Radius – Over Bucket

15ft

Width – Over Tires

6.08ft

Turning Radius: Outside of Tires

12.92ft

Turning Radius – Inside Tire

6.75ft

Rack Angle at Full Lift

51°

Dump Angle at Full Lift

50°

Rack Angle at Carry

46°

Departure Angle – Degrees

30°

Articulation Angle – Degrees

39°

Operating Weight: Bucket ^

12897lb

Tipping Load – Straight – ISO 14397-1 †

8653lb

Tipping Load – Full Turn – ISO 14397-1 †

7257lb

Operating Weight: Carriage and Tines ^^

12414lb

Tipping Load – Straight †

7416lb

Tipping Load – Full Turn †

6266lb

80% of Tip: Firm and Level EN474-3 ††

5013lb

Note (1)

*Vary with bucket

Note (2)

**Vary with tire

Note (3)

^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL),1.05 m3 (1.4 yd3) general purpose bucket.

Note (4)

^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class II carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center).

Note (5)

†Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing.

Note (6)

††Full compliance to EN474-3 and SAE J1197.

Note (7)

#HPL-A weight, tipping and rated loads are within 1% of the HPL-V.

Note (8)

Note (9)

Note: Goodyear POWERLOAD® tires can add up to approximately 140 kg (305 lb) to the full turn tip load and reduce vertical height by approximately 25 mm (1 in) compared to SPT9.

Other
- Fenders, front and rear
- Loader arm safety brace
- Lockable, fuel cap, HVAC filters, nose cone
- Ground level easy access daily service points
- Machine lifting/tie down points
- Scheduled Oil Sampling (S·O·S SM) ports, engine oil and hydraulic oil
- Recovery hitch with pin
- Paint, Electro-Coat primer, gloss topcoat
- Lockable main and side engine enclosures
Hydraulics
- Dead engine lower, lift valve, manual
- Hydraulic pilot shut off switch, in cab
- Hystat displacement pump, infinitely variable
- Motor, single drive with dedicated implement and steering pumps
- Electro-hydraulic, fully proportional controls
- Demand cooling fan, hydraulically driven
- Caterpillar HYDO^™ Advanced 10 hydraulic oil
- Implement valve, pressure compensated
- Joystick, single lever, single auxiliary roller
- Coupler/pin on attachment ready
- Multi-function lift and tilt with loader arm float
Electrical
- Lights, roading, front halogen
- Alternator, 100 amp sealed
- Service (Electronic Technician^™)
- Lights, rear stop and turn, LED
- Battery, heavy duty, 12V, 90Ah and 1,000 CCA
- Product Link^™
- Cab mounted fuse panel
- Battery disconnect switch
Power Train
- Axles, heavy duty, frame mounted with outboard planetary reduction
- Closed circuit breather Coolant, extended life, –36° C (–33° F)
- Fuel pump, priming (manual)/water separator/drain
- Air cleaner, two stage filter, with in cab audio/visual indicator on display
- Cat C2.8 engine
  –Diesel particulate filter (Fit for Life)
  –Fuel, diesel, ultra low or low Sulphur
  –Hydrostatic transmission, two speed, with inching function, “shift on the go”
  –Power train mode, hystat
- U.S. EPA Tier 4 Final and EU Stage V emissions compliant
- Drive shaft, sealed for life, universal joints Engine, auto idle shutdown, hibernation mode
- Engine oil, ECO drain tap and hose
Operator Environment
- Cab
  –Doors (2), fixed glass
  –Wipers, front and rear, full front coverage
  –Windshield, front single piece
  –Window, rear heated
  –Radio ready, speakers and wiring
  –Air vents, (4) screen, (7) directional
  –Heating, mechanical control unit
  –Sun visor, solid, front full width
  –Interior light (incandescent)
- Joystick, seat mounted, standard multifunction
  –FNR, auxiliary roller, speed range select, continuous flow, differential lock, horn
  –Arm rest, padded right, multiple position vertical height
- Seat, manual height adjustment, (cab) fabric with adjustable left arm rest, (canopy) vinyl
- ROPS/FOPS certified canopy/cab
  –12V power outlets, interior/exterior
  –Pedals, raised, foot, brake/inching, accelerator
  –Lever, parking brake
  –Cup holders (2)
  –CB radio clip, phone holder
  –Door release, internal (left and right)
  –Hook, large, coat and hard hat
  –Floormat, heavy duty, easy clean
  –Mirrors, (2) external breakaway, (1) internal
  –Operator station on isolation mounts
  –Steering wheel, spinner knob, horn in center
  –Seat belt, orange, retractable, 51 mm (2 in)
  –Storage, personal (trays [3], seat pocket)
  –Steering column, tilt adjusted
  –Column mounted multi function control: lights, roading, wipers, self canceling turn signals
  –Quick coupler switch, in cab
- Display, analog and digital
  –Gauges (2), hydraulic oil, engine coolant
  –Digital with soft touch buttons – fuel level, speed range, speedometer, service hour meter, service/maintenance information, hydraulic and power train performance and aggressiveness settings, security passcode (multiple languages)

Operator Station
- Seat belt options, multiple
- Interior light, door activated
- Joystick, FNR, twin auxiliary roller, differential lock, horn
- Mirrors (2) electronically adjustable, heated external, plus lower parabolic mirror
- Radio, FM or digital audio broadcast
- USB ports (2), interior
- Air Conditioning, automatic temperature control (ATC)
- Secondary display, front or rear view camera
- Soft touch keypad options, 8 or 16 button
- Sun visor, rear perforated
- Seat packages; deluxe or premium
- Doors, sliding windows (left and right)
- Phone holder, spring loaded
- Storage, lockable box or lockable cooled box
Power Train
- Creep and throttle lock function
- Fuel pump, priming, manual
- Cold start – jacket water heater, bypass valve
- Power train mode, utility (includes keypad)
- 40 km/h (25 mph) hydrostatic transmission, 3-speed, “shift on the go”, secondary steering and boosted brakes
- Antifreeze, extended life coolant, –50° C (–58° F)
Hydraulics
- Caterpillar Bio HYDO Advanced hydraulic oil
- Auxiliary flow, single standard (3) valve, single high flow (3) valve, dual high flow (4) valve
- Reversing fan
- Quick disconnect auxiliary hydraulics
- Ride Control or load check valves
- Connect under pressure and case drain
Electrical
- Push to start
- Work tool wiring harness, (3) in cab switches
- Lighting packages, multiple; front, rear, engine bay (LED or HAL)
Other
- Rotary sensors (snubbing, kickouts, parallel)
- Couplers, vertical (SSL), horizontal (HPL-V, HPL-A)

Cat 907 Compact Wheel Loader